My good friend Jamie was down in my cave recently and said he'd like one just like it, so, since I can actually move around again pain-free (thank you new hip!) it was time to see if my saws still worked after 15 months of inactivity (read: no income). So off to The Big Box Lumber yard I went (I know, I know, but it was Sunday and the good lumber yard was closed and I wanted to get started!)
I thought it would be fun to document the building process. All Jamie's 18-rod rack requires in the way of lumber is four 1"X5"X8' premium white pine boards:
I suppose a person could use plywood for the top and bottom of the rack, but I prefer to glue up my own wide board. I get pretty obsessive about matching up grain patterns so that its pretty tough to tell it isn't just one big board. I take the long boards and slide them around to make matches, or cut a long board to see if it will match up with itself:
Once I get the matches figured out, I cut to approximate final size. I cut maybe 4 inches longer than I need to account for possible sniping (a funny thing that happens sometimes to boards being run through a joiner) on the ends of the boards. I usually use my radial arm saw:
Things look pretty good for creating a nice wide board:
To get perfect edges with no gaps for the glue-up, I run the boards through my joiner:
Makes for nice, tight, no-gap edge. I like to use a plate (or bisquit) joiner to strengthen the bond between individual pieces of wood. The bisquits also help with alignment during the glue-up process. Here I've got the locations marked for the bisquits:
It's a handy tool to have.
Here's what a bisquit looks like:
Bisquits and glue, ready to go:
All clamped up for about 24 hours:
Attention to grain lines makes for a nice board:
Out of the clamps and getting a first coarse sanding (I love that Bosch sander, it is a hog!):
Back to the table saw to rip material for the legs and trim:
The legs are made kind of like corner boards on a house...but you can see both sides of these legs, and the inside corner is a bear to sand, so it pays to be careful and wipe up and squeezed-out glue very carefully:
Legs, trim and top and bottom in the rough:
Time to layout the 18 holes on the top and bottom:
Over to the drill press to cut out a total of thirty six 2.5" holes (oh, so boring, all puns intended):
Then the router comes out to chamfer each hole with a 1/8" roundover bit:
Chamfered and not:
Time to pick out a stain. I gave Jamie 4 choices from my Bag O' Stained wood:
He picked Min-Wax's English Chestnut. A good choice on pine.
Back to woodworking. Time to install the trim on the top and bottom. I get to use my favorite tool for this, my nice big 12" Milwaukee Sliding Compound Mitre Saw (this is starting to sound like one of those outdoor writer's testimonial tales of a fishing trip, naming names of every single piece of equipment. Hey, Milwaukee, you listening??):
It makes mitering a breeze. Here's the top ready for trim installation and clamping:
And glued up:
I am the worst when it comes to cleaning up every night. After just three days, the place is a disaster area:
So after a little policing of the area, all the pieces of the rod rack are completely sanded (I start with 100 grit, then 150, and I final-sand with 220) and ready for stain:
So I don the rubber gloves, grab a staining pad, and get it on:
All stained and ready for top coats:
I have been using Chem-Pak's Gun Sav'r Hunter Satin Gunstock finish on my projects for years. I love this stuff (ok, ok, another testimonial. Bear with me. And Chem-Pak, are YOU listening, LOL). It lays on beautifully, and dries within a couple hours. It sands like a dream, and the final coat is tough and beautiful. They have a gloss finish, too, but I've never used it. The satin finish is just so warm and nice.
After one coat (oops, should have used the tack rag a little more, lots of dust to be sanded out):
I apply a total of three coats, sanding the first two coats with 220 grit sandpaper:
Three coats complete and the rack is ready for assembly:
I rabbeted the tops of the legs so that they would sit on the base correctly:
The legs get screwed to the top from the inside; the screws don't show (it pays to pre-drill everything):
Installing the base:
There's a stained board that goes on the underside of the base that I forgot to get a photo of. Darn.
Anyway, all dressed up and ready for its spot at Jamie's house. Now, wasn't that easy??
Hopefully, Jamie's won't look like mine usually does: